When it comes to French doors and privacy, there are only so many options. I started researching some of them when we installed our French doors on our house here in Virginia. We have a larger lot (over 2 acres) and are surrounded by woods, but in the winter, the trees take their deciduous steps and distant neighbours have now got much better views into your domain. This bothers me, particularly at night when it is so dark outside and the house is lit up like a small supernova. I definitely like my privacy. What to do on a budget? Well, given I had no clue how to make French Door curtains, I purchased some and they’re fabulous and cost about $30.
We have another set of French doors in our basement and it has always bothered me that my kids could be down there playing (the video gaming is set up down there) and anyone can see into those doors too. I had originally planned to buy another set of the same style of curtains for down there, but then I remembered I actually have a ton of curtains from our various moves – yes, when you move like we do, you acquire so many things – some of which are a metallic Grey and would match the decor down there absolutely perfectly! The curtains I had purchased (pictured) looked very easy to copy the style of, so with a few modifications, I set out to repurpose my existing curtains into practical ones for the French door.
The first thing I did was measure the window opening in the door to ensure the curtains I had were long enough, they were. Then it was a matter of taking approximate measurements of the existing French door curtains to match up my gray ones. I measured the width of the curtain and realized I had to cut quite a lot off it. This is a little scary mind you as you are ruining, I mean restyling, something perfectly good. I found the best thing to do was to measure all the way down putting a small sharpie mark along the length then getting a ruler and joining these marks together, then it was just a matter of biting the bullet and cutting (if I ruined them, well I did have another back up pair that weren’t so perfect but would do). I made my curtains 26″ (66cm) wide with a half inch hem on the side that needed a new hem. Therefore, my marks were made at 26 1/2 inches (67.3 cm) across ensuring the 4 circles (normally what would go on a rod) became the feature top of my French door curtains and were evenly spaced on both sides.
With the length I cut off, I measured the amount I would need to make the two pieces that velcroed together, holding the entire curtain up when you wanted to allow daylight in. I did screw up a little bit here as I didn’t take into account the fact that the second piece wouldn’t have any hem on either end, don’t do what I did, make that second piece a fraction longer, it will make life easier and save a burnt finger when it comes to ironing that hem on. I made each of these pieces 19 1/4 ” (49cm) by 2 1/2 ” (6.35cm) PLUS hem – important you don’t forget to factor this in.
I didn’t even tell you that I wanted to do this entire project without sewing! I had lots of iron-on hemming tape and thought it would be perfect for this job.
If you have never used hemming/bonding tape, basically you use an iron to melt it together, ergo bond the fabric together at your given hemline. The iron has to be hot (so the fabric you use has to be capable of withstanding a reasonably hot iron, and you must turn the steam function off. Be careful not to touch the hemming tape with the hot iron, it will melt immediately and leave a sticky residue on your iron – if this happens, turn iron off and wait to get cold before wiping with a clean cloth that has some rubbing alcohol on it (I do not know this from experience ;)). I decided to double hem my edges because I wanted a clean ‘finished’ look, it did mean a lot more work but it looks better in my opinion. One other thing I did was to cut the hemming tape in half lengthwise as it fitted each of my little, narrow hems much better like that.
Once everything was hemmed and ironed, I folded the front of the curtain over so it gave my front a more professional finish, I used more hemming tape at the top to secure these two folds together.
I then joined the two pieces on to the back of the French door curtain like so (I pinned everything in place after I had measured it and before I permanently attached it so I could be sure it was all going to work and look nice and neat). My strips were attached 6″ in from the edges on each side.
Then it was a matter of attaching the Velcro. Again, I didn’t particularly want to sew, not that I can’t, I’m just not very good at it and don’t particularly enjoy it, so I had some sticky back Velcro from another project and just used it. This really is a matter of eyeballing and making sure they will align when joined together. Pinning helps with this too.
Finally, it was time to attach a curtain to the French door:
I love how these turned out. They match the decor down here perfectly, I had everything on hand so didn’t actually have to purchase anything and now I know we will have privacy downstairs too!
Would you try this at your house? What do you think of this project? Please come on over to Aussie Mum’s Adventures on FB and like my page: Aussiemumsadventures. You can find me on Twitter: @ozmumsadventures, on Instagram: Ozmumsadventures, on Pinterest: Aussiemumsadventures And please subscribe to my YouTube channel: Aussie Mum’s Adventures (I’m still working on it, so please have patience with me!).
One thought on “Shut the French Door!”